EN 中文

PCB板安装温控器KSD-01F


KSD-01F温控器
  系统触感温式温控器。灵敏、可靠。适用于线路板等作温度控制或热过载保护用。

1. 使用条件
① 相对湿度:在+20℃ 环境下达95%
② 大气压力:86-106Kpa
③ 工作位置:任意
2. 技术参数
① 点形式:1D或1H
② 触点负载:220VAC 1.5A 或24VDC 1.5A
③ 绝缘电阻:常温常湿 ≥50MΩ
④ 接触电阻:≤ 100 mΩ
⑤ 抗电强度:≥500VAC单幅0.35mm
⑥ 重量< 2g

-----------------------------------------
----------------------------------------------
3. 规格数据表

动作温度(

动作温度误差(

回复温度(

测试升降温速度(/min)

备注

0-30

±5

-15-15

5-10

表中的回复温度指低于动作温度

30-100

±3

10-30

5-10

105-150

±5

20-50

5-10

3.1端子 Terminal

镀银,无铅。

Silver plated.Nought of lead

 

4 基本性能参数 Basic Perfor,mance

4.1 电气参数 Dielectric Parameter

Cycles 寿命周期

Voltage 工作电压

Amps(resistive)负载电流

>10,000

48VDC

1.5

>10,000

220VAC

1.5

100,000

5VDC

0.020

100,000

5VDC

0.001

 

4.2 温度 Temperature

4.2.1 温度特性 Characteristic

例:动作温度:35±5℃;

Operating temperature;

回复温度:20±15

Max temperature restoration,Less than Operating temperature

 

4.2.2 测试方法 Test mehod

将温控器安装在测试夹具上并放置于测试区进行测试。以空气为热传导介质,在测温去放置温度计或温度传感器。在温度进入产品动作、回复温度范围检测,应保证升降温度速率不大于4℃/min,其间必须对测温区内的空气进行充分搅拌,使温度分布均匀:测温区内的温度均匀性在0.5℃以内。

During testing,the samples are clamped in the testing zone.Tesing begins when temperature in temperature-measuring zone stays in equilibrium.

The testing furnace is filed with air as heating medium,while thermometer or temperature sensor is Placed in temperature-measuring zone.Temperature increases or decreases from the first 3K of named

Action temperature at a speed of 1k/min.During testing,air must be mixed up to make the temperature Distribute sufficiently equable.Distributing equality of temperature in temperature-measuring zone must Be within ±0.5℃.

 

4.3 端子间电阻 Resistance Between Terminals

初始值 Before life: 50mΩ;

寿命后 After life:  500mΩ;

测试负载:直流6V,10mA。

Tested load:   DC6V,10mA。

4.4 绝缘电阻 Insulation Resistance

    在标准大气条件下,采用DC500V绝缘电阻表以额定电压测试大于等于100MΩ;

With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ.

4.5 电气强度 Dielectric Strength

在标准大气条件下,采用900V 50Hz的交流电压施加于引出端与地之间3min,无击穿、飞弧、闪络等。

Parts between electriferous components and non-electriferous ones can bear 1000V 50Hz AC current,which is nearly sina wave,for one minute as bearing test.Resulted no breakdown,no flashover.

4.6 使用环境温度 Ambient temperature range

-25℃~+180℃

-25℃ to +180℃

4.7 接地方式 Method Of Earth

通过温度温控器外金属板与设备接地金属相连

By means of the metal cup of thermostat connected in the earthing metal part.

5 可靠性参数 Reliability performance

5.1 实验条件 Test Conditions

环境温度20±5℃;

环境相对湿度60%~70%;

电源应为额定电压及额定频率50Hz的正弦波电源。

     在实验结果不发生异议的情况下,按下述条件实验亦可;

环境温度5~20℃;

环境相对湿度45%~85%;

电源为接近正弦波的交流电源。

Ambient temperature: 20±5℃

Ambient Relative Humidity:50%~70%

The power supply should be of sine wave,with rated volts and rated frequency of 50Hz.

     Without discrepancing the result,test maybe implemented according to the following conditions:

Ambient temperature vries between 5~20℃

Ambient relative humidity varies between 45%~85%;

The power supply should be AC nearly sine wave;

5.2 工作寿命 Working life

5.2.1 测试方法 Test method

将温控器在额定负载下给以升、降温进行触电开闭试验,最大循环频率6次/min,每开闭一次作为一个周期。产品经过规定次数的耐久性试验后性能指针应符合下列规定:

Power the sample thermostats with rated volts and max current,increase and decrease the temperature to test the opening/closing of the thermostats’s contacts.The max frequency should be 6 times/min,contact keep closed for one second.Then check the performance.

 

«动作温度100℃以下对试验初始值容许偏差再加上±5℃,100℃以上为±5%

«在标准大气条件下,采用DC500V绝缘电阻表以额定电压测试≥100MΩ。

«在标准大气条件下,采用1000V 50Hz的交流电压施加于引出端与地之间1min,无击穿、飞弧、闪络。

«Initial value of experient caused by action temperature:<100℃:±5℃;≥10℃±5%;

«With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ

«Parts between electriferous compenets and non-electriferous ones can bear 1000V 50Hz

Hz AC current,which is nearly sine wave,for one minute as bearing test.Resulted no breakdown,no flashover.

5.3 耐低温、高温和冷热冲击

   Resistance of Low Temperature、High Temperture,Cold、Heat Strike

将产品试样置于-20℃的低温箱中恒温保持1h,取出放置2h;然后将产品放置于150℃的高温箱中恒温保持1h,取出放置2h;最后将产品试样置于-20℃的低温箱中恒温保持0.5h,取出在室温环境中放置5min,再放置150℃的高温箱中恒温保持0.5h,取出在室温环境中放置5min,如此往复5个循环。试验完成后,产品性能指标应符合下列规定:

Sample thermostats are placed in the constant-temperature box with temperature of -20℃。When temperature inside levels off,keep it for 1h..Then take the saples out and place for 2h.And then place them in the constant- temperature box with the temperature of 150℃,keep for 1h after temperature levels off,and take place for 2h.Finally,keep the samples in the constant- temperature box of -20℃for 0.5h,then take out an place them in room temperature.(5 min as one circle,and for 5 circles in a row)

When experiment finished,samples should accord with the following guideline of specifications:

«动作温度100℃以下对试验初始值容许偏差再加上±5℃,100℃以上为±5%

«在标准大气条件下,采用DC500V绝缘电阻表以额定电压测试≥100MΩ。

«在标准大气条件下,采用1000V 50Hz的交流电压施加于引出端与地之间1min,无击穿、飞弧、闪络。

«Initial value of experient caused by action temperature:<100℃:±5℃;≥100℃±5%;

«With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ

«Parts between electriferous compenets and non-electriferous ones can bear 1000V 50Hz

Hz AC current,which is nearly sine wave,for one minute as bearing test.Resulted no breakdown,no flashover.

5.4耐潮湿 Dampness Resistance

将产品试样按GJB360.6规定置于温度40±5℃、相对湿度90~95%的恒温恒湿箱中48h后,产品试样应符合下列性能指标:

Samples thermostat are sealed in the instrument (conatant temperature & constant humidity),detailed as temperature of 40±5℃relative humidity of 90~95%,as per regulations of GJB360.6.After placed for 48,the samples should accord with the following guideline of specifications:

«动作温度100℃以下对试验初始值容许偏差再加上±5℃,100℃以上为±5%

«在标准大气条件下,采用DC500V绝缘电阻表以额定电压测试≥100MΩ。

«在标准大气条件下,采用1000V 50Hz的交流电压施加于引出端与地之间1min,无击穿、飞弧、闪络。

«Initial value of experient caused by action temperature:<100℃:±5℃;≥100℃±5%;

«With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ

«Parts between electriferous compenets and non-electriferous ones can bear 1000V 50Hz

Hz AC current,which is nearly sine wave,for one minute as bearing test.Resulted no breakdown,no flashover.

5.5 耐振动 Vibration Resistance

将产品试样刚性连接并固定在振动试验台上,相对上下、前后、左右各方向,避开产品动作温度上下限±10以外,以频率20~25Hz振幅3mm来回时间5min,历时1h。试验后,产品试样应符合下列性能指标:

«Sample thermostats ars fixed on the surface of board with full intension.Then vibrate the samples with frequency 20~25Hz,swing3mm,come-and-go tine 5mm,in directions of fluctuation,front-back,left-righe,for 1h.After tested.The samples should accord with the following guideline of specifications:

«动作温度100℃以下对试验初始值容许偏差再加上±5℃,100℃以上为±5%

«在标准大气条件下,采用1000V 50Hz的交流电压施加于引出端与地之间1min,无击穿、飞弧、闪络。

«Initial value of experiment caused by action temperature:< 100℃:±5℃;≥100℃±5%

«With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ

«Parts between electriferous components and non-electriferous ones can bear 1000V 50Hz AC current,which is nearly sina wave,for one minute as bearing test.Resulted no breakdown,no flashover.

5.6 耐跌落 Falling Resistance

将产品试样从200mm高度自由跌落在水泥地、石板或钢板等坚硬的水平面上,分别在各个方向跌落一次。试验后,产品性能指标应符合下列规定:

Sample thermostats fall down free,at the height of 200mm,to such solid horizontal like concrete ground,flagstone,armor plate.And falling begin respectively for one time,from the top,bottom,left,right,front and back.After experimented,the samples should accord with the following guideline of specifications:

«动作温度100℃以下对试验初始值容许偏差再加上±5℃100℃以上为±5%

«在标准大气条件下,采用DC500V绝缘电阻表以额定电压测试≥100MΩ。

«在标准大气条件下,采用1000V 50Hz的交流电压施加于引出端与地之间1min,无击穿、飞弧、闪络。

«Initial value of experient caused by action temperature:<100℃:±5℃;≥100℃±5%;

«With a DC500V megger,borne DC 500V,the tested value is over 100 MΩ

«Parts between electriferous compenets and non-electriferous ones can bear 1000V 50Hz

Hz AC current,which is nearly sine wave,for one minute as bearing test.Resulted no breakdown,no flashover.

5.7 触电温升 Contacts’ Temperature Raised

     <40K      Less than 40K

5.8 可弹性 Solderability

波峰焊接:将波峰焊炉设置温度最大260±5℃,将产品试样进行预热,预热温度≤150℃/1min,然后将产品试样引脚进行就焊接,焊接时间≤7秒。手工焊接:用≥60W电烙铁,烙铁表面温度≥280℃,单个引脚焊接时间≤15秒。

Wavrsolder process:Pot Temperature max 260±5℃. Pre-heating Temperature ≥150℃/1min.

Terminals solder.Solder time≤7s.Ramp-down rate≤7℃/s .Soldering iron≥60W.Temperature≥280℃ Solder time≤15s.

6.1注意事项 Cautious

u产品应工作于空气相对湿度<90%,无腐蚀性气体、可燃性气体和导电尘埃存在的环境内;

        The thermostat should work in environment with humidity not higher than 90%,free of caustic,flammable gas and conducting dust.

u产品安装时,应使安装板(金属板)紧贴所控器件的发热部位,并应在安装板涂上导热

        硅胶或其他性能类似的导热介质;

        When the thermostat is used to sense the temperature of solid items,its cup should be clung to the heating part of such items.Meanwhile,heat-conducting silicon grease,of other heat media of similar nature,should be applied to the cup’s surface.

u任何情况下不可使产品变形,以免破坏产品电气连接、温度特性及封闭性;

        Must be kept out of the thermostat Characteristic it will influence temperature dependability of electric

u使用过程中不可折弯引线脚,以免破坏电气连接的可靠性;

        Terminals should not be inflected,of else,it will influence the dependability of electric connection.


东莞市富宽源电子有限公司(东莞市富源电子科技有限公司)成立于1998年,主要从事安规元器件生产和销售,通过10年的改革和努力现在的富宽源已经成为集生产和销售为一体的安规元器件总汇;富宽源将继续秉持品质第一、服务客户的原则不断为广大客户提供质优价廉的产品。我公司目前主要提供如下产品: 电流保险丝-CurrentFuse 玻璃管电流保险丝 陶瓷管电流保险丝 贴片电流保险丝 电阻式保险丝 微型电流保险丝 高压电流保险丝 直流电流保险丝 交流电流保险丝 SMD-贴片式自恢复保险丝 AI-插件式自恢复保险丝 保险丝座-Fuseholder ESTMF系列保险丝座 EDKFH系列保险丝座 SKPTF系列保险丝座 AUTO--汽车保险丝座 OPWOP系列保险丝座 拉线盒式保险丝座 保险丝夹&端子 保险管座 保险座 大电流|高压保险座 温度保险丝-Thermalcutoffs 方块形温度保险丝 电阻式温度保险丝 大电流温度保险丝 陶瓷温度保险丝 铁壳温度保险丝 SW.C温度保险丝 NEC温度保险丝 艾默生温度保险丝 内桥温度保险丝 松下温度保险丝 AUPO温度保险丝 温度开关/温控器-Thermalprotector 热保护器/可恢复温控器 风筒式温控开关/温控器 马达热保护器/温控器 除霜除湿温控器/温控开关 超低温温控开关/温控器 微型温控开关/温控器 温度开关/温控器-Thermalprotector 7AM/17AM温控器 KSD301系列温开关 KSD-01F插脚温开关 9700系列方块形温控开关 BR系列温控开关 SEKIST-22温控器 压敏电阻-Varistors 压敏电阻 氧化锌压敏阻器 贴片压敏电阻 SMD压敏电阻 插件型压敏电阻 高能压敏电阻 汽车保险丝Autofuse/carfuse 小号汽车插片保险丝FY-MIN 中号汽车插片保险丝FY-ATC 大号汽车插片保险丝FY-MAX 小号叉栓式汽车保险丝FY-UF 大号汽车叉栓式保险丝FY-MF 管状|柱状汽车保险丝 其他型号汽车保险丝 过载保护器-CIRCUITBREAKER AR1/AR2系列过载保护器 W系列过载保护器 88/88A系列过载保护器 90系列过载保护器 91/91L系列过载保护器 97/98/98H系列过载保护器 带开关系列过载保护器 热敏电阻-NTC/PTCThermistor 负温度系数热敏电阻 陶瓷正温度系数热敏电阻 高分子正温度系数热敏电阻 温度传感器 湿度传感器 本公司将继续通过ISO9000质量管理体系的有效实施,使涉及企业生产经营的各个运作环节,均严谨有序,不断制造出质优价廉、适销对路的产品参与市场竞争,使企业长期保持较强的经营获利能力。同时我们将长期重视与行业知名企业合作,争取最大限度的代理权,以最优惠的价钱把产品销售给客户。
东莞市富宽源电子有限公司粤ICP备17014169号 技术支持:东莞网站建设



在线客服

在线客服

在线客服

在线客服

在线客服

在线客服

在线客服

24小时全国服务热线


在线客服